Analysis of Si-Etch Uniformity Based on RF Sheath Model in Ar/SF6 Very High Frequency Driven Capacitively Coupled Plasma Etcher = Ar/SF6 초고주파 용량성 결합 플라즈마 식각 장치에서 RF 쉬스 이론 기반의 식각 균일도 분석
저자
발행사항
서울 : 서울대학교 대학원, 2022
학위논문사항
학위논문(석사)-- 서울대학교 대학원 : 에너지시스템공학부 원자핵공학 2022. 2
발행연도
2022
작성언어
영어
주제어
DDC
622.33
발행국(도시)
서울
형태사항
x, 84 ; 26 cm
일반주기명
지도교수: 김곤호
UCI식별코드
I804:11032-000000170631
DOI식별코드
소장기관
One of the important factors for improving the process yield in semiconductor fabrication is etch uniformity. With the introduction of three-dimensional structures for highly integrated semiconductors, a high aspect ratio (HAR) etch process has emerged, and etch uniformity must consider not only the etch rate uniformity but also the uniformity of the etch profile distortions. Surface reaction control, which is a conventional approach for improving etch uniformity, has a limitation in that it is difficult to control the etch profile distortion uniformity, in particular, etch tilting. The very high frequency-capacitively coupled plasma (VHF-CCP) etcher, which is mainly used in the HAR etch process, has a non-uniform plasma distribution owing to the plasma local heating phenomenon by the VHF and the geometry of the CCP etcher with a narrow-gap. Therefore, there is a non-uniform distribution of the RF sheath that determines the characteristics of the ions incident on the wafer. To improve the etch uniformity, it is necessary to derive the forming mechanism of the RF sheath distribution that is the root cause of the etch uniformity and plasma parameters, which affect etch uniformity.
The properties of ions and electrons that respond to the applied frequency determine the characteristics of the RF sheath. Because the VHF source is faster than the ion frequency and slower than the electron frequency, the ions are incident on the wafer surface in response to the time-averaged electrode potential, which is the RF floating potential formed by the instantaneous response of electrons to the VHF. Therefore, the ion energy accelerated within the sheath is determined by the difference between the plasma potential and the RF floating potential, whereas the ion incident direction is determined as the normal direction of the sheath boundary that is perpendicular to the equipotential plane of the sheath. In this dissertation, etch uniformity analysis factors were derived based on the RF sheath model, and etch uniformity was analyzed using these factors. In addition, to confirm only the etching effect of ions incident on the wafer, Ar/SF6 plasma to which fluorocarbon gas that forms a polymer passivation layer is not added was used.
By analyzing the etch profile of the Si coupon samples arranged and etched in the radial direction, it was confirmed that the distribution of the etch profile was non-uniform under the VHF-CCP etcher. To determine the cause of the etch non-uniformity, the distribution of electron density, plasma potential, and electron temperatures were measured by the RF compensated Langmuir probe, and the RF floating potential was measured using a retarding field energy analyzer. In diagnosing the radial plasma distribution, it was confirmed that the plasma distribution in the VHF-CCP etcher is divided into three zones. Zone 1 is formed at the center of the electrode, and its area is determined by the standing wave of the harmonics of the applied VHF source. A standing wave effect-plasma series resonance phenomenon in which harmonics satisfying specific conditions are strengthened by resonance was observed. Zone 2 is an area in which the plasma density distribution is determined by the transport of charged particles at the peak density position. Zone 3 is formed by the escape of electrons at the edge of the electrode to the outside of the electrode. It was confirmed that Zone 3 expanded into the electrode as the electron mean free path increased.
The ion energy flux and sheath thickness distributions, which are the etch uniformity analysis factors, were determined using the radial distribution of plasma parameters. The ion energy flux and etch rate correlate with an adjusted R2 of 0.97, and the mean absolute error between the sheath thickness gradient and etch tilting was 0.002. Therefore, the etch uniformity can be analyzed using the ion energy flux and sheath thickness gradient. It was demonstrated that the plasma parameters affecting the etch uniformity were electron density and sheath voltage.
In this dissertation, based on the RF sheath model, it was confirmed that the physical phenomena that determine the radial distribution of the narrow-gap VHF-CCP etcher for each zone are different, and the plasma parameters affecting the uniformity of the etch rate and etch tilting were derived. Based on these results, it was revealed that plasma distribution improvement is essential for the improvement of etch uniformity to increase process yield, and it was proposed that an improvement strategy optimized for each zone is required to improve etch uniformity.
반도체 공정에서 공정 수율을 향상시키기 위한 중요한 인자 중 하나는 식각 균일도이다. 고집적 반도체를 위해 3D 구조가 도입됨에 따라 고종횡비 식각 공정이 등장하였고, 이에 따라 식각 균일도는 단순한 식각률 균일도뿐만 아니라 식각 형상 불량의 균일도까지 고려해야 한다. 기존의 식각 균일도 개선 접근 방법인 표면 반응 제어는 식각 형상 불량, 특히 식각 기울기의 균일도의 제어가 어렵다는 한계를 가진다. 고종횡비 식각 공정에서 주로 사용되는 설비인 초고주파 용량성 결합 플라즈마 식각 장치는 초고주파에 의한 플라즈마 국소 가열 현상 및 좁은 간격을 가진 장치 구조에 의해 불균일한 플라즈마 분포를 갖는다. 이에 따라 웨이퍼에 입사하는 이온의 특성을 결정하는 RF 쉬스의 분포가 형성된다. 식각 균일도 개선을 위해서는 식각 균일도 분포를 야기하는 근본 원인인 RF 쉬스 분포의 발생 기작 및 식각 균일도에 영향을 미치는 플라즈마 인자 도출이 필요하다.
이온과 전자가 인가 전원에 반응하는 속도에 따라 RF 쉬스의 특성이 결정된다. 초고주파 전원은 이온 주파수보다 빠르고 전자 주파수보다 느린 특징을 가지므로, 이온은 시 평균 된 RF 전위에 반응하여 웨이퍼 표면에 입사한다. 따라서 이온이 쉬스 내에서 받는 에너지는 플라즈마 전위와 RF 부유 전위의 차이로 결정된다. 또한, 이온의 입사 방향은 쉬스 등 전위면의 수직인 쉬스 경계의 법선 방향으로 결정된다. 본 논문에서는 이 RF 쉬스 모델을 기반으로 식각 균일도 해석 인자를 도출하고, 이를 이용하여 식각 균일도를 해석하였다. 또한, 웨이퍼에 입사하는 이온에 의한 식각 영향만을 확인하기 위해 폴리머 보호층을 형성하는 탄화불소가스가 첨가되지 않은 Ar/SF6 플라즈마를 사용하여 연구하였다.
반경 방향으로 배치하여 식각한 Si 시편의 식각 결과를 분석한 결과, 초고주파 용량성 결합 플라즈마 식각 장치에서의 식각 형상 분포가 불균일함을 확인하였다. 불균일을 야기하는 원인을 파악하기 위해 보상형 랭뮤어 프로브로 전자 밀도 및 전자 온도의 분포를 진단하고, 지연장 에너지 분석기로 RF 부유 전위 분포를 진단하였다. 반경 방향 플라즈마 분포를 진단한 결과, 초고주파 용량성 결합 플라즈마 식각 장치 내 플라즈마의 분포가 크게 3가지 영역으로 나뉘는 것을 확인하였다. 영역 1은 전극 중심부에 형성이 되며, 인가 주파수의 고조파가 형성하는 정상파에 의해 영역 1의 범위가 결정된다. 특정 조건을 만족하는 고조파가 공진 현상을 일으키며 강화되는 정상파 효과-플라즈마 직렬 공진 현상이 관측되었다. 영역 2는 피크 밀도 위치에서 하전 입자들의 이동에 의해 플라즈마 밀도 분포가 결정되는 영역이었다. 영역 3은 전극 가장자리에서의 전자가 전극 외부로 탈출하는 현상에 의해 형성된다. 전자의 평균 자유 행로가 길어질수록 영역 3은 전극 내로 확장되는 것을 확인하였다.
측정된 플라즈마 인자를 이용해 식각 균일도 해석 인자인 이온 에너지 플럭스 분포 및 쉬스 두께 분포를 계산하였다. 이온 에너지 플럭스와 식각률은 수정된 R2 0.97 이상의 상관관계를 가졌고, 쉬스 두께 구배와 식각 기울기를 비교하면 평균 절대 오차 0.002 수준의 오차를 가지는 것을 확인하였다. 따라서 이온 에너지 플럭스와 쉬스 두께 구배로 식각 균일도를 해석할 수 있음을 확인하였고, 식각 균일도에 영향을 미치는 플라즈마 인자는 전자 밀도와 플라즈마 전위와 RF 부유 전위의 차인 쉬스 전압임을 밝혔다.
본 연구를 통해 RF 쉬스 모델을 바탕으로 좁은 간격을 가진 초고주파 용량성 결합 플라즈마 식각 장치의 플라즈마 분포를 결정하는 물리 현상이 영역별로 다름을 확인하였고, 식각률과 식각 기울기 균일도에 영향을 미치는 플라즈마 인자를 도출하였다. 이 결과를 바탕으로 공정 수율 향상을 위한 식각 균일도의 근원적 개선을 위해서는 플라즈마 분포 개선이 필수적임을 밝혔으며, 식각 균일도 개선을 위해서는 영역별 최적화된 개선 전략이 필요함을 제시하였다.
분석정보
서지정보 내보내기(Export)
닫기소장기관 정보
닫기권호소장정보
닫기오류접수
닫기오류 접수 확인
닫기음성서비스 신청
닫기음성서비스 신청 확인
닫기이용약관
닫기학술연구정보서비스 이용약관 (2017년 1월 1일 ~ 현재 적용)
학술연구정보서비스(이하 RISS)는 정보주체의 자유와 권리 보호를 위해 「개인정보 보호법」 및 관계 법령이 정한 바를 준수하여, 적법하게 개인정보를 처리하고 안전하게 관리하고 있습니다. 이에 「개인정보 보호법」 제30조에 따라 정보주체에게 개인정보 처리에 관한 절차 및 기준을 안내하고, 이와 관련한 고충을 신속하고 원활하게 처리할 수 있도록 하기 위하여 다음과 같이 개인정보 처리방침을 수립·공개합니다.
주요 개인정보 처리 표시(라벨링)
목 차
3년
또는 회원탈퇴시까지5년
(「전자상거래 등에서의 소비자보호에 관한3년
(「전자상거래 등에서의 소비자보호에 관한2년
이상(개인정보보호위원회 : 개인정보의 안전성 확보조치 기준)개인정보파일의 명칭 | 운영근거 / 처리목적 | 개인정보파일에 기록되는 개인정보의 항목 | 보유기간 | |
---|---|---|---|---|
학술연구정보서비스 이용자 가입정보 파일 | 한국교육학술정보원법 | 필수 | ID, 비밀번호, 성명, 생년월일, 신분(직업구분), 이메일, 소속분야, 웹진메일 수신동의 여부 | 3년 또는 탈퇴시 |
선택 | 소속기관명, 소속도서관명, 학과/부서명, 학번/직원번호, 휴대전화, 주소 |
구분 | 담당자 | 연락처 |
---|---|---|
KERIS 개인정보 보호책임자 | 정보보호본부 김태우 | - 이메일 : lsy@keris.or.kr - 전화번호 : 053-714-0439 - 팩스번호 : 053-714-0195 |
KERIS 개인정보 보호담당자 | 개인정보보호부 이상엽 | |
RISS 개인정보 보호책임자 | 대학학술본부 장금연 | - 이메일 : giltizen@keris.or.kr - 전화번호 : 053-714-0149 - 팩스번호 : 053-714-0194 |
RISS 개인정보 보호담당자 | 학술진흥부 길원진 |
자동로그아웃 안내
닫기인증오류 안내
닫기귀하께서는 휴면계정 전환 후 1년동안 회원정보 수집 및 이용에 대한
재동의를 하지 않으신 관계로 개인정보가 삭제되었습니다.
(참조 : RISS 이용약관 및 개인정보처리방침)
신규회원으로 가입하여 이용 부탁 드리며, 추가 문의는 고객센터로 연락 바랍니다.
- 기존 아이디 재사용 불가
휴면계정 안내
RISS는 [표준개인정보 보호지침]에 따라 2년을 주기로 개인정보 수집·이용에 관하여 (재)동의를 받고 있으며, (재)동의를 하지 않을 경우, 휴면계정으로 전환됩니다.
(※ 휴면계정은 원문이용 및 복사/대출 서비스를 이용할 수 없습니다.)
휴면계정으로 전환된 후 1년간 회원정보 수집·이용에 대한 재동의를 하지 않을 경우, RISS에서 자동탈퇴 및 개인정보가 삭제처리 됩니다.
고객센터 1599-3122
ARS번호+1번(회원가입 및 정보수정)