공진 특성 조절이 가능한 Otto 구조의 표면 플라즈몬 공명 센서에 대한 연구
저자
발행사항
전주: 전북대학교 일반대학원, 2021
학위논문사항
학위논문(박사)-- 전북대학교 일반대학원 전자.정보공학부(전자공학) 2021. 2
발행연도
2021
작성언어
한국어
주제어
발행국(도시)
전북특별자치도
기타서명
Study on Otto configuration based surface plasmon resonance with tunable resonance characteristics
형태사항
xii, 135 p.: 삽화, 도표; 26 cm
일반주기명
전북대학교 논문은 저작권에 의해 보호받습니다.
지도교수: 김정무
참고문헌 : p. 125-135
UCI식별코드
I804:45011-000000052955
소장기관
Surface plasmon polaritons are collective oscillation of electrons in the surface of the metals such as gold, silver and aluminum and it is caused by the incident light. When the specific conditions such as angle of incidence, wavelength and refractive index of materials, are satisfied, the incident light can be absorbed as a surface plasmon polaritons and the reflectance is rapidly decreased. This phenomenon is called as surface plasmon resonance. Characteristics of the surface plasmon resonance is changed sensitively according to a dielectric constant and refractive index change of the materials near the metal surface. Thus, if target molecules contact on the metal surface, surface plasmon resonance effect is changed and we can use this system as a sensor. The surface plasmon resonance sensor has been widely used in the chemical biology and drug design with advantages of label free detection, room temperature detection, and real time monitoring. There are two types of coupling configuration for surface plasmon resonance system using thin metal film. In the kretschmann configuration, metal film is located on the glass surface. On the other hand, metal film of the Otto configuration is located with a distance of the few micrometers from the glass. Due to the robust structure and convenience of fabrication, most of the surface plasmon resonance sensors are based on the kretschmann configuration. However, Otto configuration has a potential for tunable resonance characteristics according to the air-gap distance. If the air-gap distance between the glass substrate and the metal thin film can be stably adjusted, it will be possible to use a surface plasmon resonance sensor with the structural flexibility of the Otto configuration.
In this study, the Otto configuration based sensor was fabricated through silicon on quartz bonding process. An air-gap distance of the sensor was designed to be 2.2 um and whole size of the sensor is 30*30*1 mm^3. Characteristics of the sensor was measured using a laser module with wavelength of 975.1 nm and the results was compared with FEM simulation results. It was verified that the characteristics can be sensitively changed according to the refractive index of the metal film.
Performance of the sensor for gas sensing application was verified with simulation results and the results was compared with those of the other researches. The sensitivity of the fabricated sensor is 55 degree/RIU where the refractive index of the sensing medium is varied from 1 to 1.008.
To verify the potential of the fabricated sensor as a pressure sensor, resonance characteristics was measured with applied pressure level from 0.23 bar to 1.3 bar. The air-gap distance of the fabricated Otto configuration was varied according to the pressure and the resonance characteristics was also changed. From the measurement results, the sensor has a sensitivity and resolution of about 0.17 degree/bar and 0.029 bar, respectively, as a pressure sensing application. Results show that the fabricated Otto configuration based sensor can be used as a hazardous gas and pressure level of the industrial facility with high sensitivity.
Otto configuration with stepped air-gap (1.86 um, 2.42 um, 3.01 um, 3.43 um) was fabricated and the resonance characteristics at each air-gap was measured with 980 nm laser source. Minimum reflectance is measured to be 0.688, 0.716, 0.766, 0.86 at each section and the measurement results was analyzed with FEM simulation results.
To verify the variability of characteristics of the Otto configuration and its applicability, the air-gap between the prism and the metal film was adjusted by using a commercial piezoelectric actuator. When the wavelength of the incident light was 786 nm, the reflectance was measured as 0.25 where the displacement of the piezoactuator was about 10.5 um, and it was confirmed that the maximum surface plasmon resonance occurred. Likewise, when a light source having a wavelength of 977 nm is used, the minimum reflectance becomes 0.22 where the displacement of the piezoactuator is about 9.3 um. The results shows that the wavelength of incident light for the maximum surface plasmon resonance in the Otto configuration is proportional to the air-gap in the actual measurement results.
With an aim of inducing the variability of characteristics of the Otto configuration, a serpentine spring based MEMS actuator was designed and the driving characteristics were theoretically analyzed through numerical calculation and FEM simulation methods. The MEMS actuator for adjusting the air-gap of the Otto configuration was designed based on low-resistivity silicon. A 200 nm-thick gold thin film is located on the upper surface of the driving part. The initial distance between the silicon driving part and the driving electrode on the surface of the glass substrate is designed to be 18 um, and the distance between the gold film and the glass substrate is adjusted to be about 1 um from the initial value of 6 um.
A resonance frequency of the driving part was calculated to be about 1.34 kHz, and it was confirmed that the driving part of the designed MEMS actuator can maintain a stable state even if an external shock is applied. FEM simulation results show that driving part of the proposed sensor can be moved vertically as much as 5.1 um when a potential difference of 59.2 V is applied between the driving electrode on the glass substrate and the driving part.
It is expected that the results of this study can be used as a background data for the development of Otto configuration based surface plasmon resonance sensors with variable resonance characteristics, which has not been reported so far.
분석정보
서지정보 내보내기(Export)
닫기소장기관 정보
닫기권호소장정보
닫기오류접수
닫기오류 접수 확인
닫기음성서비스 신청
닫기음성서비스 신청 확인
닫기이용약관
닫기학술연구정보서비스 이용약관 (2017년 1월 1일 ~ 현재 적용)
학술연구정보서비스(이하 RISS)는 정보주체의 자유와 권리 보호를 위해 「개인정보 보호법」 및 관계 법령이 정한 바를 준수하여, 적법하게 개인정보를 처리하고 안전하게 관리하고 있습니다. 이에 「개인정보 보호법」 제30조에 따라 정보주체에게 개인정보 처리에 관한 절차 및 기준을 안내하고, 이와 관련한 고충을 신속하고 원활하게 처리할 수 있도록 하기 위하여 다음과 같이 개인정보 처리방침을 수립·공개합니다.
주요 개인정보 처리 표시(라벨링)
목 차
3년
또는 회원탈퇴시까지5년
(「전자상거래 등에서의 소비자보호에 관한3년
(「전자상거래 등에서의 소비자보호에 관한2년
이상(개인정보보호위원회 : 개인정보의 안전성 확보조치 기준)개인정보파일의 명칭 | 운영근거 / 처리목적 | 개인정보파일에 기록되는 개인정보의 항목 | 보유기간 | |
---|---|---|---|---|
학술연구정보서비스 이용자 가입정보 파일 | 한국교육학술정보원법 | 필수 | ID, 비밀번호, 성명, 생년월일, 신분(직업구분), 이메일, 소속분야, 웹진메일 수신동의 여부 | 3년 또는 탈퇴시 |
선택 | 소속기관명, 소속도서관명, 학과/부서명, 학번/직원번호, 휴대전화, 주소 |
구분 | 담당자 | 연락처 |
---|---|---|
KERIS 개인정보 보호책임자 | 정보보호본부 김태우 | - 이메일 : lsy@keris.or.kr - 전화번호 : 053-714-0439 - 팩스번호 : 053-714-0195 |
KERIS 개인정보 보호담당자 | 개인정보보호부 이상엽 | |
RISS 개인정보 보호책임자 | 대학학술본부 장금연 | - 이메일 : giltizen@keris.or.kr - 전화번호 : 053-714-0149 - 팩스번호 : 053-714-0194 |
RISS 개인정보 보호담당자 | 학술진흥부 길원진 |
자동로그아웃 안내
닫기인증오류 안내
닫기귀하께서는 휴면계정 전환 후 1년동안 회원정보 수집 및 이용에 대한
재동의를 하지 않으신 관계로 개인정보가 삭제되었습니다.
(참조 : RISS 이용약관 및 개인정보처리방침)
신규회원으로 가입하여 이용 부탁 드리며, 추가 문의는 고객센터로 연락 바랍니다.
- 기존 아이디 재사용 불가
휴면계정 안내
RISS는 [표준개인정보 보호지침]에 따라 2년을 주기로 개인정보 수집·이용에 관하여 (재)동의를 받고 있으며, (재)동의를 하지 않을 경우, 휴면계정으로 전환됩니다.
(※ 휴면계정은 원문이용 및 복사/대출 서비스를 이용할 수 없습니다.)
휴면계정으로 전환된 후 1년간 회원정보 수집·이용에 대한 재동의를 하지 않을 경우, RISS에서 자동탈퇴 및 개인정보가 삭제처리 됩니다.
고객센터 1599-3122
ARS번호+1번(회원가입 및 정보수정)